(Identical to ASTM Specification A /A M (R) except for deletion of , revision of Table 1 footnote A, and editorial corrections to Table 2.) 1. A Class B Stressproof TG&P Cold Finished Bar Round Turned Ground Polished, A Round Bar, A Rod, A TG&P Rod, A TG&P Round Rod . See the chemical composition and physical properties of ASTM A Grade cold-drawn, stress relieved, annealed bar, find alternative materials, and.
|Published (Last):||22 February 2009|
|PDF File Size:||13.21 Mb|
|ePub File Size:||1.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
Niagara Lasalle Steel Products – Stressproof ®, ASTM A, Cold Rolled Steel Round Rod
For continuous type of treatment, a lot adtm consist of 25 tons [25 Mg] or less of the same size of each heat, treated in the same cycle.
It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The yield strength shall be determined at 0.
Restricted Incidental Elements S2. The results then become an integral part of the quality assurance program. Every order is inspected for surface defects with a magnetic or roto bar tester.
axtm Historical Version s – view previous versions of standard. The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other.
ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. One warpage test is taken of first bar asym by a new or reground specialty designed drawing die. One class, B, is cold drawn with higher than normal heavy drafts to provide higher strength levels, and four grades provide improved machinability.
It covers multiple grades and numerous conditions of stress-relieved cold drawn bars to meet minimum mechanical property requirements. Aatm B are heavy-draft cold-drawn and stress-relieved rounds and hexagons.
Therefore, a warpage test is always performed on the first bar drawn through either a new or reground die.
ASTM A311 Grade 1117 cold-drawn, stress relieved, annealed bar
The area of the sample to be examined should be agreed upon between adtm purchaser and the manufacturer, and the test specimen should be hardened by heating and quenched before being polished to avoid pits. Workmanship, Finish, and Appearance The values stated in each system are not exact equivalents, therefore, each system must be used independently of the other. Niagara LaSalle developed this groundbreaking process a3111 and forever changed the economics of part production.
NOTE 2— When turned bars are speci? To further improve quality, Niagara LaSalle reduced the standard seam depth tolerance for StressProof from 0. NOTE 1— A typical ordering description is as follows: Parts you are now heat treating from Rc 23 to Rc Seams deeper than that stated above are rejected.
To learn more about StressProof or any of our specialty products, please contact us. Within the limits of good manufacturing and x311 practices, the bars shall be free of injurious seams, laps, segregation, or other imperfections that, due to their nature, degree, or extent, will interfere with the use of the material in machining or fabrication of suitable parts.
An optical comparator test is made of a mold from each new or reground die measuring the internal geometry of the die. The primary melting may incorporate separate degassing or re?
Restricted Cast or Heat Analysis the surface of the material. Maximum seam depth of 0.
You can rely on Niagara LaSalle for all of your steel bar needs. This abstract is a brief summary of the referenced standard.
A Steel Bar | Capital Steel & Wire
The importance of high temperature stress relieving to obtain wstm ductility, minimum warpage and excellent machinability is a major part of the original patent. This was followed by the highest temperature stress relieving treatment possible to q311 a combination of properties, including strength, wear resistance, minimum warpage and excellent machinability. A lot shall consist of bars of the same size from the same heat which have been stress relieved in the same stationary furnace charge.
And, most importantly, help reduce your manufacturing costs. Ground and Polished with special close tolerances available on order. Materials and Manufacture 6. If restraightened, then the same number of tests are again required. Tension test shall be made to conform to the requirements specified.
Link to Active This link will always route to the current Active version of the standard. This specification covers cold-drawn, stress-relieved carbon steel bars subject to mechanical property requirements.
The result is a steel bar product that meets stringent standards and provides a wide variety of benefits, including:.